MODEL

PLP-45-12

PLP-45-24

PLP-45-48

OUTPUT

DC VOLTAGE

12V

24V

48V

CONSTANT CURRENT REGION Note.4

9 ~ 12V

18 ~ 24V

36 ~ 48V

CURRENT RANGE

0 ~ 3.8A 

  0 ~ 1.9A

0 ~ 0.95A

RATED CURRENT

3.8A

1.9A

0.95A

RATED POWER

45.6W

45.6W

45.6W

RIPPLE & NOISE (max.)  Note.2

4.2Vp-p

3.8Vp-p

4.8Vp-p

VOLTAGE ADJ.RANGE

2.85 ~ 3.8A

1.425 ~ 1.9A

0.715 ~ 0.95A

VOLTAGE TOLERANCE   Note.3

10%

LINE REGULATION

3.0%

LOAD REGULATION

5.0%

SETUP, RISE TIME

1000ms / 230VAC 2000ms / 115VAC at full load

HOLD UP TIME (Typ.)

INPUT

VOLTAGE RANGE

90 ~ 264VAC 127 ~ 370VDC

FREQUENCY RANGE

47 ~ 63Hz

POWER FACTOR

PF  0.9 at 75 ~ 100% load, 115VAC / 230VAC

EFFICIENCY (Typ.)

86%

89%

89%

AC CURRENT (Typ.)

0.6A/115VAC 0.3A/230VAC

INRUSH CURRENT (Typ.)

42A/230VAC

LEAKAGE CURRENT

<0.75mA / 240VAC

PROTECTION

OVERCURRENT

100 ~ 110%

Protection type : Constant current limiting, recovers automatically after fault condition is removed

SHORT CIRCUIT

Protection type : Hiccup mode, recovers automatically after fault condition is removed

OVER VOLTAGE

15 ~ 18V

28 ~ 33V

57 ~ 63V

Protection type : Shut down o/p voltage, re-power on to recover

OVER TEMPERATURE

ENVIRONMENT

WORKING TEMP.

-30 ~ +70 (Refer to output load derating curve)

WORKING HUMIDITY

20 ~ 95% RH non-condensing

STORAGE TEMP., HUMIDITY

-40 ~ +80 , 10 ~ 95% RH

TEMP. COEFFICIENT

0.03%/ (0 ~ 50 )

VIBRATION

10 ~ 500Hz, 2G 12min./1cycle, period for 72min. each along X, Y, Z axes

SAFETY &EMC(Note 4)

SAFETY STANDARDS

TUV EN61347-1, EN61347-2-13 approved ; design refer to UL60950-1

WITHSTAND VOLTAGE 

I/P-O/P:3.75KVAC I/P-FG:1.88KVAC O/P-FG:0.5KVAC

ISOLATION RESISTANCE

I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH

EMI CONDUCTION & RADIATION

Compliance to EN55015

HARMONIC CURRENT

Compliance to EN61000-3-2 Class C( 75% load); EN61000-3-3

EMS

IMMUNITY

Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024,EN61547, light industry level, criteria A

OTHERS

MTBF

 586.5Khrs min. MIL-HDBK-217F (25 )

DIMENSION

101.6*50.8*29.6mm (L*W*H)

PACKING 

0.16Kg; 96pcs/16.4Kg/0.89CUFT

NOTE

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25     of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. Constant current operation region is within 60% ~100% rated output voltage. This is the suitable operation region for LED related applications, but please reconfirm special electrical requirements for some specific system design.

5. Derating may be needed under low input voltages. Please check the static characteristics for more details.

6. Safety and EMC design refer to EN60598-1, CNS15233, GB7000.1, FCC part18.

7. Length of set up time is measured at cold first start. Turning ON/OFF the power supply may lead to increase of the set up time.

8. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.