MODEL

APV-12-5

APV-12-12

APV-12-15

APV-12-24

 OUTPUT

DC VOLTAGE

5V

12V

15V

24V

CURRENT RANGE

2A

1A

0.8A

0.5A

RATED CURRENT

0~2A

0~1A

0~0.8A

0~0.5A

RATED POWER

10W

12W

12W

12W

RIPPLE & NOISE (max.)  Note.2

100mVp-p

120mVp-p

120mVp-p

150mVp-p

VOLTAGE TOLERANCE   Note.3

5.0%

LINE REGULATION

1.0%

LOAD REGULATION

2.0%

SETUP, RISE TIME

1500ms, 30ms / 230VAC 1500ms,30ms / 115VAC at full load

HOLD UP TIME (Typ.)

20ms/230VAC          15ms/115VAC at full load

INPUT

VOLTAGE RANGE

90 ~ 264VAC 127 ~ 370VDC

FREQUENCY RANGE

47 ~ 63Hz

EFFICIENCY (Typ.)

76%

80%

80%

80%

AC CURRENT (Typ.)

0.2A/230VAC     0.35A/115VAC

INRUSH CURRENT (Typ.)

COLD START 35A/115VAC          70A/230VAC

LEAKAGE CURRENT

0.25mA / 240VAC

PROTECTION

OVER CURRENT

Above 105% rated output power

Protection type : Hiccup mode, recovers automatically after fault condition is removed

OVER VOLTAGE

5.75 ~ 6.75V

13.8 ~ 16V

17.5 ~ 21V

28 ~ 32V

Protection type : Shut off o/p voltage, clamping by zener diode

ENVIRONMENT

WORKING TEMP.

-30 ~ +70 (Refer to output load derating curve)

WORKING HUMIDITY

20 ~ 90% RH non-condensing

STORAGE TEMP., HUMIDITY

-40 ~ +80 , 10 ~ 95% RH

TEMP. COEFFICIENT

0.03%/ (0 ~ 50 )

VIBRATION

10 ~ 500Hz, 5G 12min./1cycle, period for  72min. each along X, Y, Z axes

SAFETY &EMC(Note 4)

SAFETY STANDARDS

Design refer to TUV EN60950-1, EN61347-2-13,UL8750

WITHSTAND VOLTAGE 

I/P-O/P:3KVAC

ISOLATION RESISTANCE

I/P-O/P:>100M Ohms / 500VDC / 25 / 70% RH

EMI CONDUCTION & RADIATION

Compliance to EN55022 (CISPR22) Class B,EN55015,EN61547

HARMONIC CURRENT

Compliance to EN61000-3-2 Class A, EN61000-3-3

EMS

IMMUNITY

Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, light industry level(surge 2KV),  criteria A

 OTHERS

MTBF

Khrs min.      MIL-HDBK-217F (25 )

DIMENSION

77*40*29mm (L*W*H)

PACKING 

Kg;          pcs/        Kg/        CUFT

 NOTE

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. Derating may be needed under low input voltage. Please check the static characteristics for more details.

5. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the

complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.

6. Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time.